Design and locomotion analysis of two kinds of rolling expandable mobile linkages with a single degree of freedom

Frontiers of Mechanical Engineering - This study presents two kinds of rolling robots that are able to roll by deforming their outer shapes with a single degree of freedom. Each robot is an...     

Relative vibration identification of cutter and workpiece based on improved bidimensional empirical mode decomposition

Frontiers of Mechanical Engineering - In the process of cutting, the relative vibration between the cutter and the workpiece has an important effect on the surface topography. In this study, the...     

Removal of Cu2+ from Water Using Liquid-Liquid Microchannel Extraction

The very good extraction selectivity of Cu²⁺ from water was demonstrated with a new microchannel equipment, by employing di-(2-ethylhexyl)phosphoric acid (D2EHPA) as an extractant and kerosene as a solvent. The effects of different experimental parameters on the extraction efficiency E, the volumetric mass transfer coefficient K_La, and the entrainment were experimentally investigated. The results showed that the extraction efficiency increased with increasing temperature, extractant concentration, phase ratio (organic/aqueous), and pH. The total flow rate, phase ratio, and pH were found to have a great effect on the mass transfer, whereas the temperature and the extractant concentration showed little effect.     

The biological mechanisms of butanol tolerance and the application of solvent-tolerant bacteria for environmental protection

Toxicity caused by the accumulation of butanol in fermentation media is an important factor limiting the concentration of butanol. There is currently no systematic research in place investigating the butanol tolerance mechanism of bacteria such as Clostridium acetobutylicum, which adapts to butanol stress and regulates its growth and metabolism. Here, research results related to the butanol tolerance of C. acetobutylicum are reviewed to understand the molecular basis of changes in butanol-tolerant strains. Organic solvent-tolerant bacteria play an important role in the fields of biofuel production, enzyme preparation and bioremediation. An analysis of limitations of the application of organic solvent-tolerant bacteria has revealed that future research should focus on combining the microbial tolerance phenotype with specific utilization to achieve an optimal balance between organic solvent tolerance and production. This review serves as a reference for the improvement and engineering of strains that tolerate organic solvents. © 2019 Society of Chemical Industry     

巨型工程机械子午线轮胎高强度、低生热胎面基部胶配方开发

通过对国外知名品牌37.00R57和40.00R57规格巨型工程机械子午线轮胎胎面基部胶组成分析和物理性能测试,对我公司巨型工程机械子午线轮胎胎面基部胶配方进行优化设计。新开发配方半成品和成品胶料动态损耗因子分别降低37.9%和26.6%,胶料物理性能达到竞品水平,成品轮胎TKPH提升13.6%。     

剂油比对煤焦油沥青质加氢过程的影响

以中低温煤焦油沥青质为原料,采用NiMoW/γ-Al_2O_3商业催化剂,在反应温度380℃、反应压力8 MPa和反应时间1.5 h条件下,分别在不同剂油质量比(1∶25、1∶20、1∶15、1∶10)条件下进行加氢实验,通过采用元素分析、FT-IR、XRD、~1H-NMR和XPS等分析表征手段,考察不同剂油质量比对中低温煤焦油沥青质加氢转化过程的影响。结果表明,随着剂油质量比的增加,沥青质转化率提高,加氢产物分布也发生大幅变化,沥青质和芳香分轻质化转化为饱和分。但随着剂油质量比的进一步提高,同时也发生了更多的裂化反应和缩合反应,剂油质量比在合适范围能够很好地起到加氢轻质化且抑制结焦的效果。     

湖北省保康县荆山玉地球化学特征及其成因分析

荆山玉是湖北省保康县新发现的一个玉石品种,形成于大陆边缘—洋盆区过渡带的热水沉积环境,为晚震旦世—早寒武世灯影组的一种硅质角砾岩:原地震碎角砾岩,由角砾和胶结物二部分构成,角砾局部可拼接;角砾成分为早期硅质岩碎裂产物,胶结物除早期硅质岩碎裂产物外,还有少量后期充填的石英、铁质等,受角砾、胶结物颗粒大小、裂隙发育程度不同的影响,后期热液改造程度不同,角砾和胶结物化学成分存在一定的差异,色调与铁质有关。荆山玉的形成主要经历了三个阶段的演化:第一阶段,低温150～225℃、弱氧化—弱还原条件下热水成因的硅质岩形成;第二阶段,热力膨胀外力作用下,硅质岩局部原地震碎形成硅质角砾岩,热水温度243～340℃,富氧氧化—贫氧过渡环境,红褐色的Fe~(3+)在胶结物、裂隙中富集;第三阶段,热水温度116～127℃、缺氧还原条件,黄色的Fe~(2+)在胶结物、裂隙中富集。     

Simultaneous improvement of thermal conductivity and mechanical properties for mechanically mixed ABS/h-BN composites by using small amounts of hyperbranched polymer additives

Recently, thermal interface materials (TIMs) are in great demands for modern electronics. For mechanically mixed polymer composite TIMs, the thermal conductivity and the mechanical properties are generally lower than expected values due to the sharply increased viscosity and poor filler dispersion. This work shows that addition of a small amount of polyester-based hyperbranched polymer (HBP) avoided the trade-off in mechanically mixed ABS/hexagonal boron nitride (h-BN) composites. After adding 0.5 wt% HBP, the maximum h-BN content in the composites increased from 50 to 60 wt%. The out-of-plane, in-plane thermal conductivity, and tensile strength of ABS/h-BN with 50 wt% h-BN were 0.408, 0.517 W/mK, and 18 MPa, respectively, and were increased to 0.729, 0.847 W/mK, and 32 MPa by adding 0.5 wt% HBP, while 0.972, 1.12 W/mK, and 29.5 MPa were achieved for ABS/h-BN/HBP with 60 wt% h-BN. The morphological and rheological results proved that these enhancements are due to the improved h-BN dispersion by decreasing viscosity of composites during mixing. Theoretical modeling based on the modified effective medium theory confirmed such results and showed that the interfacial thermal resistance also decreased slightly. Thus, this work demonstrates a facile and scalable method for simultaneously improving the thermal conductivity and mechanical properties of thermoplastic-based TIMs.